|
|
S100
Enclosed Infant Seat
A fully enclosed infant seat
prevents small children from falling out. Vandal proof, it is constructed of 3/8
EPDM rubber and Polymer blend
( ELASTOMER
), .020 stainless steel insert and heavy duty rust proof hardware.
National Test Lab Results: 500 lb. Grade: Commercial.
|
$66.41
-1 Each
|
|
|
S103
High Back Infant Seat
The same as our rubber
infant seat but With smaller leg openings to meet under age 2 ruling.
Made of EPDM rubber and Polymer blend
( ELASTOMER
). Comes with a stainless steel insert. National Test Lab Results: 500+ lbs.
Grade: Commercial
|
$68.98
|
|
|
S110 Strap Seat
This colorful and durable Belt seat
is 6" x 24" x 3/8" thick, with a .025 stainless steel insert with
stainless steel washers welded to each side, They have a 1/2"
hole that requires large end
S-hook or H-shackle to be used for connecting the chain.
Made of EPDM rubber and Polymer blend
( ELASTOMER
).
National Test Lab
Results: 547+ lb. Grade: Commercial.
|
$29.75
-1 Each
|
|
|

|
S115 Bumper Seat
An extra piece of fluted
rubber at the front and back of this seat gives it a cushion bumper for added
safety. It is made with a .020 stainless steel insert to resist vandalism.
Made of EPDM rubber and Polymer blend
( ELASTOMER
) and galvanized triangular hardware.
National Test Results: 500+ lbs. Grade: Commercial.
|
$30.90
-1 Each
|
|
|
|
S127 Roto Molded Flat Seat
This seat is made of
polypropylene. it is available in bright colors that will not fade. These
seats are made wider and sturdier to hold both small and large children.
The dimensions are 20" long by 8" at the narrowest portion, to 9" wide at
the widest section of the seat, and 2" high. This seat meets ASTM
standards and can be used commercially or for residential use. This seat
is extremely durable. National Test Results: 500+ lbs. Grade: Commercial.
|
$47.00
-1 Each
|
|
|
S130 Strap
Seat W/Tri-Angle Hardware
Vandal Proof Commercial Swing
Seat with galvanized triangle hardware makes this one of our sturdiest swing
seats. It is
Made of EPDM rubber and Polymer blend
( ELASTOMER
), with a .020
carbon steel insert to prevent vandalizing, and measures 6” x 24” x 5/16”
thick. National Test Lab Results: 5573 lb.
Grade: Commercial.
|
$28.90
-1 Each
|
|
|
S150 Half Bucket Seat
Commercial Tot Seat with Stainless Steel Insert. An exceptional tot seat,
Made of EPDM rubber and Polymer blend
( ELASTOMER
)
5/16” thick,
and with a .020 stainless steel insert to prevent vandalism.
SAFETY CHAIN IS NOT
INCLUDED.
National Test Lab Results: 3300 lb.
Grade: Commercial.
SAFETY
CHAIN Click Here.
|
$38.70
-1 Each
|
|
|
S175 Rotational
Molded Full Bucket Seat
Our rotational molded infant seat made of polypropylene. It is
available in bright colors that will not fade. These seats meet ASTM standards,
and can be used both commercially or residentialy. The extra wide hanger is
especially designed so that the seat is gravitationally correct when a child is
swinging in the seat. The hanger is made of stainless steel. This seat is
extremely durable, and should hold up well in all applications. This seat is 12"
across, 11 1/2" front to back, leg holes 6 1/2" in diameter and the seat is 8"
deep. National Test
Lab Results: 500+ lbs. Grade: Commercial.
|
$99.40
-1 Each
|
CREATED BY
Chiggerknob Swings Cal, Copyright © 2004-06
[California Swing Products, Div. of Chiggerknob Swings].
All rights reserved. Updated 11-21-07
|